this post was submitted on 12 Nov 2023
509 points (94.7% liked)
Memes
8383 readers
936 users here now
Post memes here.
A meme is an idea, behavior, or style that spreads by means of imitation from person to person within a culture and often carries symbolic meaning representing a particular phenomenon or theme.
An Internet meme or meme, is a cultural item that is spread via the Internet, often through social media platforms. The name is by the concept of memes proposed by Richard Dawkins in 1972. Internet memes can take various forms, such as images, videos, GIFs, and various other viral sensations.
- Wait at least 2 months before reposting
- No explicitly political content (about political figures, political events, elections and so on), [email protected] can be better place for that
- Use NSFW marking accordingly
Laittakaa meemejä tänne.
- Odota ainakin 2 kuukautta ennen meemin postaamista uudelleen
- Ei selkeän poliittista sisältöä (poliitikoista, poliittisista tapahtumista, vaaleista jne) parempi paikka esim. [email protected]
- Merkitse K18-sisältö tarpeen mukaan
founded 2 years ago
MODERATORS
you are viewing a single comment's thread
view the rest of the comments
view the rest of the comments
I fucking hate Phillips style so much.
Never tried JIS though, Robertson is where it's at.
Do you have a moment to talk about our Lord and Savior Torxus Christ?
Torx is the one true god
And his disciples are Pozidrive
Who TF still uses Phili... Oh, it's you lot again 🤣
The knock off Robertson? Why would I use that
What is the reason to use torx over Internal hex (Allen key)? Surely there must be a reason why it's used
When growing up it used to be that (internal) hex was for high strength but needed exact tool size, and Phillips/flat blade for low strength application with the benefit of any approximately sized tool will work.
Seems to me torx is in this awkward in-between where it's used for low-strength applications, but require exact tool size. Or it's used interchangeably with hex, requiring two sets of tools available at the work site (not fun if the work site is 30 meters up some ladders)
You can get more torque on a torx than an Allen. They're basically the same shape, but torx has longer contacts on the star points where the hex corners would be.
Also, M1.5 hex is getting a little too close to a circle, and you can forget about going much smaller. M1.5 torx is still usable.
Also (for the same reasons) Torx heads don't have to be as deep for the same torque as an Allen. More space efficient.
Torx is a lot less likely to strip out the tool or the fastener than Allen, especially at smaller sizes. Torx comes in a smaller variety of sizes than Allen does, so it's more difficult to choose a slightly wrong size. Especially with Allen being offered in both metric and moon landing fractionals, there's like, M0.8, and 14/93", one of which fits slightly loosely in the other and will sorta work, until you turn real hard on a stubborn bolt and round out the screw and/or driver.
In other words, it is my experience that you'll have a large pile of allens that you can't realistically tell apart, and a set of like 8 Torx tips from which you only use like three.
I see. It makes sense when you say it.
Yet I only encounter torx on low-medium torque stuff. Applicances, not cars.
Jeep doors are T50
Found the Canadian
But not #1, or most of #2, in common stainless alloys. Even dry film lubed and drill tip is insufficient to prevent the torque from exceeding the (relatively low) yield strength, leading to stripped screws from standard driving in any wood denser than about G=0.45. There's simply not enough contact area to prevent it.
Stainless fasteners are niche and require stainless tools, full-stop.
Most fasteners are not stainless.
You really don't want to use stainless tools as they will plastically deform. Roberson is just not that great for torque-transfer geometry; it's advantages lie elsewhere.
They are made specifically for stainless fasteners.
You'll frequently find them in the toolbags of aerospace professionals and industrial electricians and they are really the only folks that deal with a lot of stainless fasteners.
Bicycle and motorbike folks have lots of stainless hardware, too. And lots of time you'll see folks blame JIS/Phillips on ruining their fasteners, but sometimes it's just because they're using toolsteel tools on stainless fasteners.