114
submitted 2 years ago by [email protected] to c/[email protected]
all 25 comments
sorted by: hot top new old
[-] [email protected] 89 points 2 years ago
[-] [email protected] 115 points 2 years ago* (last edited 2 years ago)

Here's the specific bit relavent to OP's question:

VAWTs often suffer from dynamic stall of the blades as the angle of attack varies rapidly.

The blades of a VAWT are fatigue-prone due to the wide variation in applied forces during each rotation. The vertically oriented blades can twist and bend during each turn, shortening their usable lifetimes.

Other than the drag-types, VAWTs have proven less reliable than HAWTs,[20] although modern designs have overcome many early issues.

VAWT = vertical axis wind turbine

HAWT = horizontal ...

[-] [email protected] 37 points 2 years ago
[-] [email protected] 8 points 2 years ago

Horizontal Axis WInd Turbines. So HAWT right now

[-] [email protected] 7 points 2 years ago

So take off all your clothes!

Best Hot In Herre video: https://youtu.be/XNGjSll2_Uc?feature=shared

[-] [email protected] 3 points 2 years ago

Here is an alternative Piped link(s):

https://piped.video/XNGjSll2_Uc?feature=shared

Piped is a privacy-respecting open-source alternative frontend to YouTube.

I'm open-source; check me out at GitHub.

[-] [email protected] 3 points 2 years ago

This has drifted so far away from the original question

[-] [email protected] 6 points 2 years ago

I don't know why, the big fan is on

[-] [email protected] 13 points 2 years ago

So TL;DR it's worth the extra bearing for the added efficiency unidirectional wind flow allows.

[-] [email protected] 1 points 2 years ago

Didn’t one fall over a while back in NYC area?

[-] [email protected] 29 points 2 years ago
[-] [email protected] 10 points 2 years ago

New community found

[-] [email protected] 15 points 2 years ago* (last edited 2 years ago)

Because money/practical limitations: It costs more to make them and in ye olden times I'm not sure they had the technology to make a reliable vertical axis turbine.

They do exist these days, but aren't as common because they're more expensive and complicated (which also means more maintenance, which further adds to the long-term cost).

[-] [email protected] 5 points 2 years ago

And if you really notice, your wind in most regions usually comes from about the same direction anyhow. It's known as prevailing winds, and it how sailors managed to get anywhere they were going. Basically, towards the equator winds blow to the west, and at about the 30 degree mark away from the equator the winds blow towards the east (towards northeast, often in the north, and southeast in the south).

[-] [email protected] 3 points 2 years ago

Pardon my ignorance but, how is a vertical wind turbine more mechanically complicated than a "standard" one?

[-] [email protected] 2 points 2 years ago* (last edited 2 years ago)

I'm not an engineer but as I understand it: They are harder to make than a traditional windmill. Mechanically probably wasn't the best word to use I guess, at least for most designs.

[-] [email protected] 11 points 2 years ago

I guess it could be that it's easier to build. You have a tower that only gives structural support and you have a gondola that only deals with all the rotation. In general it is difficult to have something that rotates and also carries a large load. And the rotating gondola technology is a solved problem. Plus you have a large rotor area that is always facing the wind instead of half your blade area going opposite to the wind. These are just guesses though.

[-] [email protected] 11 points 2 years ago* (last edited 2 years ago)

They aren't as efficient that way. Horizontal axis wind turbines most of the time have their whole "swept area" in unobstructed airflow. For vertical turbines the blades pass into the turbulent air from the other blades and the vertical post.

The swept area of a horizontal turbine is increases more for a given amount of additional blade length than a vertical turbine as well. Extending the radius of a circle creates more swept area than an equivalent increase of length or width of a rectangle.

[-] [email protected] 2 points 2 years ago

I guess you would have to canalize the wind, cause it would press against the entire wheel. In which direction should it turn when you don't want to construct something more complex to have more pressure on only one side of the wheel.

[-] [email protected] 2 points 2 years ago

they work best when the axis is parallel to direction of wind flow

this post was submitted on 02 Nov 2023
114 points (99.1% liked)

Asklemmy

48488 readers
763 users here now

A loosely moderated place to ask open-ended questions

Search asklemmy 🔍

If your post meets the following criteria, it's welcome here!

  1. Open-ended question
  2. Not offensive: at this point, we do not have the bandwidth to moderate overtly political discussions. Assume best intent and be excellent to each other.
  3. Not regarding using or support for Lemmy: context, see the list of support communities and tools for finding communities below
  4. Not ad nauseam inducing: please make sure it is a question that would be new to most members
  5. An actual topic of discussion

Looking for support?

Looking for a community?

~Icon~ ~by~ ~@Double_[email protected]~

founded 6 years ago
MODERATORS