this post was submitted on 21 Apr 2024
45 points (97.9% liked)

3DPrinting

15561 readers
186 users here now

3DPrinting is a place where makers of all skill levels and walks of life can learn about and discuss 3D printing and development of 3D printed parts and devices.

The r/functionalprint community is now located at: [email protected] or [email protected]

There are CAD communities available at: [email protected] or [email protected]

Rules

If you need an easy way to host pictures, https://catbox.moe may be an option. Be ethical about what you post and donate if you are able or use this a lot. It is just an individual hosting content, not a company. The image embedding syntax for Lemmy is ![](URL)

Moderation policy: Light, mostly invisible

founded 1 year ago
MODERATORS
[email protected]
[email protected]
[email protected]
[email protected]
45
What causes this on PLA? Too little cooling? Or possibly too much?? (lemmy.world)
submitted 6 months ago by [email protected] to c/[email protected]
13 comments fedilink hide all child comments
 

Anyone have any idea what might cause this sort of issue on PLA? I run into it frequently, but pretty much only when all of the following points are true:

  • the print has multiple parts, so the extruder spends a decent amount of time off of any given part (only one part from this print is pictured)
  • the affected part(s), like the picture above, have a relatively steep outward overhang, extending over the build plate
  • the outward overhang part is relatively narrow, as seen from a top view

This is from a printer with a 4028 fan (i.e. pretty massive airflow, server type fan) so even the 35-45% (based on layer time) I have it currently set at is more than 100% with single/dual 5015's or etc.

I guess my other option is to try supports, but this doesn't really seem like a situation where supports should be needed. Anyone ever had a similar problem and solved it without just turning the speed waaaayyyyyy down?

top 13 comments
sorted by: hot top controversial new old
[–] [email protected] 11 points 6 months ago

I'm not sure I understand. What is it supposed to look like.

[–] [email protected] 7 points 6 months ago* (last edited 6 months ago)

this looks like its warping from too much heat. you can try:

lowering temperatures, more cooling or slower printing

also is your bed leveled? sometimes this can happen because the extruder is too close on some points but not on others. from that angle it looks like its not warping evenly.

give us more details about your setup if you can, temps, printer type etc.

[–] [email protected] 3 points 6 months ago (1 children)

This can sometimes be caused by uneven cooling. I was able to resolve it by using a fan shroud that cools on both sides of the print.

[–] [email protected] 3 points 6 months ago (1 children)

Thank you! I should have mentioned this nozzle has a dual fan duct! sides!

[–] [email protected] 4 points 6 months ago (1 children)

I'm seeing quite a few strings there around the nozzle and fan ducts. Another thing that can cause that curling is wet filament, which will also cause the stringing. So you might also try drying it.

Do you see the same curling with other filaments?

[–] [email protected] 1 points 6 months ago* (last edited 6 months ago) (2 children)

Good question! I probably could try drying this filament again, just for kicks...I did dry it not too long ago but it's probably been long enough that it couldn't hurt. But yes I've seen this issue with virtually every PLA filament I've used when the factors I mentioned are all true.

When this failure occurred, I was about 100 filament swaps in (it's a multicolor print) so faint evidence of the nozzle purging/eject/reload/etc process in the midst of powerful fans is at least initially what I had attributed that to.

[–] [email protected] 2 points 6 months ago

From my experience that glitter filament seems to absorb moisture a little faster than some filaments. I keep mine in a drybox all the time.

[–] [email protected] 1 points 6 months ago

My Rapido makes fine whispy strings like that when I'm printing too hot, but I've never tried PLA on mine.

[–] [email protected] 3 points 6 months ago

How fast are you trying to print? Does it behave differently if you slow down?

One of the reasons prints can shrink like this is that the speed is essentially stretching the plastic as it comes out the nozzle, like a rubber band. As the plastic settles that tension pulls it together.

I doubt moisture is the issue, PLA doesn't actually absorb water very quickly.

Also, have you done a temperature tower and flow calibrarion for this filament?

[–] [email protected] 2 points 6 months ago

It's been a while since I've printed but I think both my sidewinder and voron do this. I don't remember having it after switching to abs. Painted on supports and wider extrusions helped a ton if I remember correctly. Good luck!

[–] [email protected] 1 points 6 months ago* (last edited 6 months ago) (1 children)

Based on your fans it's more likely too much air + high initial temperature causing uneven cooling. I assume with those fans you're trying to print really fast?

[–] [email protected] 2 points 6 months ago

Well...fast by Ender/etc. standards lol but nowhere near pushing Ratrig performance envelopes here lol. Pretty much stock profile speed wise

[–] [email protected] 0 points 6 months ago

From the brown blobs and warping, it's printing way too hot, which youve probably done to compensate for an overabundance of cooling. Slow the fan, slow down, and lower the temperature.