17
Looking for device for Home Assistant (lemmy.ml)
submitted 5 months ago by to c/asklemmy@lemmy.ml
11 comments fedilink hide all child comments
 

Hi everyone. I'm looking for a device to install Home Assistant on to manage a smart thermostat, a programmable light bulb (on and off), and another lamp in my house. Since I'll be doing other work in the future, I want to use Home Assistant to be ready for the future.

That said, I'm looking for a device (a Mini PC, a Pi, etc.) that consumes very little power, as I'll be using it exclusively for this purpose. Do you have any suggestions? Thank you in advance!

all 11 comments

sorted by: hot top controversial new old
[–] 16 points 5 months ago (1 child)

If running Home Assistant is all you are going to do, Pi is enough. There's also official hardware with Home Assistant preinstalled: Home Assistant Green

  • permalink
  • fedilink
  • source
  • hideshow 2 child comments
    •
    • [–] 9 points 5 months ago (1 child)

    Can't go wrong with a pi. I'm using a pi4 for mine with a sonoff usb ZigBee dongle. Can't give you accurate power consumption but it'll be fairly minimal I would think.

  • permalink
  • fedilink
  • source
  • hideshow 2 child comments
    •
  • [–] 8 points 5 months ago (2 children)

    Beware, HomeAssistant absolutely eats SD cards.

    A pi booting from an SD card is a good way to test it out, but HA does so much logging and other writing to storage that the write limit on the card gets used up very quickly. Took my setup only like a month or two to die when I first started with HA.

    If you want to run HAOS on a pi long-term, you will need to set up a different boot drive that can handle more lifetime writes.

  • permalink
  • fedilink
  • source
  • parent
  • hideshow 4 child comments
    •
  • [–] 2 points 5 months ago (1 child)

    My pi3+ has been running for 8+ years on the same card. I ran out of processing and ram before the sd gave out. I only buy top-notch a2 cards.

    I just upgraded to a pi5. To handle all of the integrations and devices I've added over the years. Still plan to stay on the sd until the price of other options comes down again.

  • permalink
  • fedilink
  • source
  • parent
  • hideshow 2 child comments
    •
  • [–] 4 points 5 months ago

    Would be a good idea to check how close you are to the write limit, then. Pricier cards have a higher write limit, but all SD cards are limited.

    Luckily, once you hit the limit, it turns read-only, so you can move to a new card pretty easy, but it will happen eventually.

    Neat to know you've got a longer life out of the card you bought, though! I'll have to look into cards that have a higher write limit for my next Pi project!

  • permalink
  • fedilink
  • source
  • parent
    • [–] 4 points 5 months ago (1 child)

    I used to run it on a pi. I got a nuc 11 a while back so I could upgrade the ram/storage. But never had a real issue with either.

    Home assistant also makes the green and yellow.. I don't have them, but they don't seem to consume much energy.

    https://www.home-assistant.io/green/

    https://www.home-assistant.io/yellow

  • permalink
  • fedilink
  • source
  • hideshow 2 child comments
    •
  • [–] 5 points 5 months ago

    They don’t make the yellow anymore, the green is good from what I hear though if you are just looking for home assistant and don’t expect to add a bunch of other apps to it (z2mqtt, node-red, etc.).

  • permalink
  • fedilink
  • source
  • parent
    • [–] 2 points 5 months ago

    Any newer Pi should be fine for a basic setup. I ran HA on a raspberry pi 3 B for years with no performance issues.

  • permalink
  • fedilink
  • source
    •
    [–] 2 points 5 months ago

    To add a question to OPs question, is there an instance that has a HomeAssistant channel? Or smart home in general? I thought I saw one at one point...

  • permalink
  • fedilink
  • source
    •